Supply ring high pressure blower +0.75KW vortex high pressure blower
RB-750A ring high pressure blower with points:
1, with blowing and suction dual function, a dual-purpose machine, you can use suction, you can also use hair;
2, less oil or no oil operation, the output of the air is clean;
3. Relative to the centrifugal fan and medium-pressure fan, the pressure is much higher, more than ten times that of the centrifugal fan;
4, the pump body is an overall Die Casting, and the use of shock mounting feet, then its requirements for the installation of the foundation is very low, and even can not use the fixed foot can be normal operation, very convenient, but also very save installation costs and Installation cycle
5, Relative to the same type of fan, its operation noise is low;
6, maintenance-free use; its loss parts are only two bearings, within the warranty period, basically do not require maintenance;
8, easy to install, easy to use!
RB-750A annular high pressure blower It is mainly used for: combustion oxygen reducer, cigarette filter tip forming machine, electroplating tank liquid mixing, atomizing dryer, water treatment aeration, screen printing machine, photo platesetter, injection molding machine, automatic Feeding dryer, liquid filling machine, powder filling machine, welding equipment, film machinery, paper transportation, dry cleaning clothes, cleaning, drying, conveying, powder, air dusting, dry bottles, gas transmission, feeding, collection, Environmental protection water treatment, central dust collection and environmental protection, electroplating, dust removal, food, packaging, filling, glass products, air flow transportation and other industries.
Direct Taiwan wind fan, explosion-proof fan, medium pressure fan, high pressure fan, high pressure annular fan, centrifugal fan, all-air blower, through Pu fan, vortex pump, gas ring vacuum pump, the whole high pressure fan is China's fan industry The high-end products, performance higher than similar products, the whole wind high pressure fan made of special materials:
1. The blades and covers of the high-pressure fan of the whole wind are made of the hardest ADC12 material in the world, which is equivalent to that of Mercedes-Benz wheel steel rings.
Second, the whole high-pressure blower bearings using high-speed, high temperature resistant imported bearings, in the case of 50Hz 2800 rev / min, in the case of 60Hz 3450 rpm / minute, free lubrication, maintenance-free. Support 24 hours of long-term operation, stable and reliable performance.
Third, all the high-pressure fan inlet and outlet are equipped with a built-in silencer, so as to achieve low noise.
Fourth, the whole wind high pressure fan 1.1KW the following models can be used at full pressure.
Fifth, the pressure of the whole-air high-pressure fan is stable. It is proved through the example of water treatment and electroplating treatment that the stirring is even and the height of the water wave is consistent.
Sixth, the whole wind high pressure fan under the same power, the same pressure, the flow is greater than similar products. Seventh, the whole high-pressure air blower fan cover adopts the sheet heat dissipation design, which is equivalent to a motorcycle engine heat sink, which greatly reduces the temperature of the fan when it is running.
Eight, the whole high-pressure fan adopts the principle of front bearing design. The two bearings are located at the front end of the fan blade and the rear end of the motor to achieve the best dynamic balance configuration and facilitate heat dissipation. (The reason is that the fan blades have heat sinks at the front end to dissipate heat, and the rear-end bearings work under the fan's own cooling fan to keep the bearings working at low temperatures for long periods of time.)
Nine, the whole high-pressure fan uses a special shock-proof foot design, which greatly reduces the vibration generated in the operation of the fan.
Ten, the whole wind high pressure fan economical and energy saving. With the same power, the same pressure, and the same flow, the current of the high-pressure fan of the whole wind is lower than other similar products.
Brass strip has good mechanical properties, good plasticity in hot state, good plasticity in cold state, good machine ability, easy to be fiber-welded and welded, corrosion resistant.Brass milling parts be processed by machine tool trajectory by means of computer controlled machine, using high speed rotating cutting tool if you want to shape the material. With the size of products have become increasingly demanding, Machining from the original two gradually changed to 3 axis machining, 4 axis machining, 5 axis machining center, precision can reach 0.001mm. Machine tool spindle speed 20000RPM to ensure that the surface of the workpiece is smooth and clean.we often processed material of Brass.
In addition to, we also provide high precision machining and precision machined parts,supply custom machining services and CNC machining services for small batch.
Brass CNC Milling Machining,Brass Machined Parts,CNC Milling Machining Brass Parts,Brush Brass Parts
YaoPeng Metal Products Co., Ltd. , http://www.ypmfg.com