Recalling data to sort out which car parts frequency "invited"?

In 2017, 200.48 million defective cars were recalled, and the number was even higher!

According to the data from the AQSIQ, in 2017, major domestic automotive product manufacturers implemented a total of 251 recalls of defective automotive products, recalled 200.48 million defective vehicles, and increased 77% on the basis of a breakthrough of 10 million vehicles in 2016. A record high, and for the fourth year in a row, the number of annual recalls has been updated.

♦ Four cars have been recalled

Since the implementation of the recall system for defective automotive products in China in 2004, a total of 1,548 vehicle recalls have been implemented, and 5.738 million defective vehicles have been recalled. Among them, the party has implemented 1013 recalls since the 18th National Congress of the Party and recalled 47.99 million defective vehicles. , accounting for 83% of the total recall in 14 years. Judging from the overall number, China has implemented a recall of almost one in every four vehicles.

Not only has the total amount of recalls been large, the growth rate of China’s auto recalls has also been rising year after year. In the past three years, the annual number of recalls of defective automobiles in China was 5.586 million vehicles, 11.335 million vehicles, and 20.048 million vehicles, which each exceeded an annual growth rate of more than 50%. The number of annual recalls has far exceeded that of developed countries such as Germany, Britain, and Japan. Second only to the United States.

♦Airbags and other components are frequently used

In recent years, engine, transmission, clutch, brake system, steering system, front and rear axles and suspension systems, body accessories and electrical appliances, tires and eight categories of parts and components are the focus of consumer complaints. At the same time, the number of car recalls caused by the major assembly companies is also increasing.

According to AQSIQ data, airbags and seat belt assemblies have the largest number of recalls, involving 10.683 million vehicles, accounting for 53.1% of the total number of recalls; the second is the engine assembly, involving 4.096 million vehicles, accounting for the total number of recalls. 20.4%; third is the steering system assembly, involving 1.757 million vehicles, accounting for 8.8% of the total number of recalls; and the fourth is the electrical equipment assembly, involving 1.655 million vehicles, accounting for 8.3% of the total number of recalls; The vehicle body assembly involves 805,000 vehicles, accounting for 4% of the total number of recalls.

Not only that, there are still frequent recall problems caused by a single component in the 2017 defective automobile recall, and there is a trend of multiple brand, cross-regional, and centralized defects in automotive product defects. For example, as of 2017, a total of 38 auto companies in the Gaotian airbag incident had recalled 126 times, involving 19,516,000 vehicles, which was the most recalled recall in recent years. In 2017 alone, there were 29 auto companies with 36 recalls and involved 9.87 million vehicles.

In addition, the simultaneous implementation of global recalls has become more and more normalized. According to statistics, 58% of the 251 defective vehicle recalls implemented this year were global recalls, and relevant producers actively ensured that global recall activities were simultaneously released in the Chinese market and implemented in the same period. At the same time, more and more cases of global recalls triggered by China's defect investigations in recent years, such as the investigation of fuel pump defects, prompted Volkswagen to recall 1.818 million vehicles in China and triggered a global recall.

The level of manufacturing in the automotive industry is improving, and the quality supervision of parts and vehicles is also improving, but the number of vehicle recalls remains high. The primary factor is that China’s car ownership is increasing, and the probability of parts problems is increasing. At the same time, the increase in the number of recalled cases is also a manifestation of car companies' safeguarding consumer rights and social responsibility. Of course, mistakes and defects in the work of product quality are the root cause of the recall.

Therefore, it is particularly important to improve the quality management system for parts and components companies, not only to innovate in quality management, but also to strictly control quality management and reduce the failure rate of parts and components in order to provide good protection for the vehicle.

technical parameters

Product brief introduction

PCH set Hammer Crusher is suitable for crushing cement, building materials, chemical industry, electric power, metallurgy, and other industrial sectors broken compressive strength less than 150 mpa various brittle materials, such as limestone, materials such as coke, coal crusher, finely work.

Company Introduction

Luoyang Hong Xin Heavy Co., LTD. is located in Luoyang Xin'an Industrial Park, Luoyang Hongxin Heavy Machinery Co., Ltd is an enterprise featured with industrial designing, processing and manufacturing, which is qualified for import-export trade. Covering an area of 15,000 square meters and holding an annual production value of 80 million RMB, the company of 20 million RMB registered capital has total 100 staff members, among which there are 20 engineering technicians owning senior and medium professional titles and 40 intermediate and senior technicians capable of product designing and developing.

Hongxin is dedicated to produce reducers, hoists, crushers, Ball Grinding Mills and the equipments of screening, coal washing, metallurgy and cement, and replacement parts. Meanwhile, we provide the perform maintenance service for various series of equipments. There are 52 large-scale equipments applied into the manufacturing process, such as T200 CNC floor boring and milling machine, YK 73125 CNC molding gear grinding machine, YK322B CNC molding gear grinding machine, Y3200 gear hobbing machine, Y1600 CNC gear sharper, 4m vertical lathe, 6.3m CNC vertical lathe, T110 CNC boring machine, and 52 middle-sized productive and assistive equipments, which integrate strong manufacturing and processing capability with complete managing system of production and technology, quality management system and comprehensive testing measures.

Certificates

Contacts

Hammer Crusher

Hammer Crusher,Professional Hammer Crusher,High Efficiency Hammer Crusher,Ring Hammer Crusher

Luoyang Hongxin Heavy Machinery CO., TLD. , https://www.hxreducer.com