Of depleted of chromium ore beneficiation, we have used jigger, shaker, spiral concentrator, centrifugal concentrator and belt chute sorting through all over the chromium depleted ore (Cr203 <20%), but also with the hydraulic tube sorter sorting Pass the shaker in the mine. Dry strong magnetic separation, wet strong magnetic separation, flotation and various chemical beneficiation methods were studied in the laboratory. However, in the actual production, the re-election method is mainly adopted, and individual mines adopt strong magnetic separation.
Since 1967, China has built five small ore dressing plants in Zunhua, Beijing, Miyun, Shangnan, Inner Mongolia, Sauran, Inner Mongolia, and Salto, Xinjiang. The first three have been selected with the end of mining. Discontinued. The existing Solon Mountain plant was built in 1985. The designed scale has an annual output of 3,000-4,000 tons of concentrate powder, 25% of the ore grade, 40% of the refined grade after re-election, but the tailings grade is 10%. In 1986, it was put into production for the strong magnetic separation process.
Currently our chrome ore smelting mainly Pyrometallurgy electric furnace method, followed by metal vacuum thermal reduction and carbon reduction and converter method. The electric furnace method is further divided into a mineral thermal method and a refining electric furnace method. The former carbon as reducing agent, chromium ore, coke, silica raw materials to produce high-carbon ferrochrome, silica or coke, the raw material for the production of high carbon ferrochrome sichrome; the latter using silica as a reducing agent, chromium ore , silicon chrome alloy, lime as raw material to produce medium and low carbon ferrochrome and micro carbon ferrochrome. It is also useful to produce medium and low carbon ferrochrome in a converter.
Metal thermal reduction method commonly used as a reducing agent aluminum particles, chromium oxide vigorous reaction in a short time, emit large amounts of heat, melting the chromium.
The vacuum carbon reduction method uses high-grade chromium ore (currently used high-carbon ferrochrome after oxidizing roasting) as an oxidant, and is made into agglomerates with high-carbon ferrochrome powder, placed in a vacuum furnace, and decarburized at a temperature lower than the melting point of the metal. , production of micro-carbon, ultra-fine carbon ferrochrome; or decarburization and nitrogen gas to produce nitrogen-containing ferrochrome alloy.
Wet smelting is currently carried out by oxidizing roasting of chrome ore and soda ash and dolomite or limestone into a rotary kiln to form sodium chromate. After water immersion, sodium sulfide or sulfur is added to reduce it to chromium hydroxide precipitate, and dehydration calcination to obtain oxidation. Chromium is then produced by metal thermal reduction or vacuum carbon reduction and electrolysis.
In addition to the above smelting methods, in recent years, China has studied the method of recovering chromium from Jinchuan copper- nickel tailings in Gansu, which uses oxidizing roasting to prepare chromium hydroxide, then chrome ammonium ruthenium, and finally metal chromium. The Chinese Academy of Sciences has also developed a new process for the extraction of chromium by primary amines. The extraction rate of chromium is 98% and the stripping rate is 100%. The purity of Cr203 product is 95%-98%, which provides a basis for comprehensive utilization of associated chromium in the red iron ore of Panzhihua-Xichang area.
Standard: ANSI/ASME B16.5, JIS B2220, KS B1503, EN1092-1, UNI, DIN, BS, AWWA, API, MSS, SABS, ASA, GOST standard
Method: By forging, Forged Flange, stainless Steel Flange
Pressure: 5K-30K (JIS B2220/KS B1503), 150Lbs - 2500Lbs (ANSI), PN6-PN100 (DIN, UNI, EN1092-1)
Size: 1/2"- 80", DN15-DN2000.
Type: Welded Neck, Blind, Threaded, Lap Joint, Socket Weld, SOH, SOP, Slip On (SO) FF, RF, Plate
Material: 304, 316L
Marking: On Required
Packing: Wooden Pallets
Painting: Rust-preventative oil painting or Black/yellow/varnish painting or Galvanizing
Quality control: Internal/ ISO9001, KS approval etc
Inspection: Internal / Third party
Certificate: Material certificate, Physico-chemical analysis certificate etc.
Types' Specification
Welding neck
1, Preferred for high-pressure, subzero or elevated temperature
2, Hub is tapered and bored to match pipe's inside diameter so flow is not restricted, preventing turbulence and reducing erosion
3, Easily radiographed and provides excellent stress distribution
Slip-on
1, Not normally used in high-stress applications due to low hub and weld attachment
2, Silps over outside of pipe
3, Inside of flange welded at hub and end of pipe
Lap joint
1, Used where bolt alignment or access for cleaning is required
2, Similar to slip-on flange when used with lap joint stub end
3, Radius at intersection of flange face and bore to match lap joint stub end
Threaded
1, Used where welding would would be hazardous
2, Designed for low-pressure and non-cyclic applications
3, Bore is threaded to match pipe thread
4, Tapered to seal pipe and flanges
Socket welding
1, For small-diameter chemical processes, hydraulic and stream distribution lines
2, Similar to slip-on flange
3, Counter bore matches pipe bore, allowing unrestricted flow
4, Counter bore from hub side fits pipe's outer diameter can insert pipe in socket with fillet weld at hub
Blind
1, Used to close ends of piping
2, Has no bore
3, Permits access to sealed lines
Other flanges
Orifice, Expander, Reducing, Lightweight, Studding Outlets, Long Weld Necks,Metric, Navy Drawings, Customer Drawings
FAQ:
1.Are you a trader or manufactor?
We are a manufactor (Own Forging workshop and CNC machining workshop )
2.Can your products reach to FDA , CE and 3A requirements?
Yes, all of our material can reach to the requirements of FDA, ISO and 3A Certificate).
3.We can supply:
Sanitary Butterfly Valve, Sanitary Check Valve and Diaphragm Valves, as well as Various Tank Accessories: Sight Glass, Strainers/Filter, Cleaning Ball, And other Pipe Fittings , (Pipe Unions: SMS, DIN, IDF, RJT, 3A,DS; Fittings: Ferrule,Elbow, Tee, Reducer and all other Non-standrad fittings), each products are tested well by our strictly Quality Control System, and we also have excellent service to support you and promote your business.
4.Lead Time:
For large quantity, as usual, it can be sent out within 20-40 days.
Small parcel will be dispatched by DHL, FedEx, UPS OR TNT Courier.
Big cargo will be delivered by Air freight or By Sea.
5.Our Service:
About payment:
Payment methods: L/C, T/ T, Paypal,Western Union
6.About samples:
We can provide samples production and service. Usually 2 to 5 days, the sample can be sent to your hands. We will choose the shipping way as you required: By sea, by air or by express. Any question about samples, please contact us.
7.For OEM products:
We will finish the production within 20-40 days after payment has been confirmed.
About delivery and shipping:
We will choose the delivery way as you required: By sea, by air, by express ect. Save your cost is our mission.
8.Warranty:
Any question or problem will be respond within 12 hours.
9.Lifetime service:
Any problem happened to our product, we will do our best to help client to solve it, spare parts will be half price in lifetime.
10.Problem solve:
If you can't solve the problem in your local, please delivery the product to us, we will repair it and then back to you.
11.Quality control:
All the products are calibrated with real working condition, and tested before shipping as qualified product.
12.Purpose:Attitude is everything.
Flange Bearing,Steel Flange,Forged Flange,Welding Neck Flange
Wenzhou Qili Fluid Equipment Co., Ltd. , https://www.qlssvalve.com