Mass Flow Meter-Coliolis Flow Meter-Measuring The Mass, Volume, Density

Flow Fluid Measured: Liquid, Air, Solid Flow
Output Signal: 4-20mA, Pulse, RS485, Hart
Indicate: Flow Rate, Total Flow, Density, Temperature
Fluid Types: Two-Phase Flow, Three-Phase Flow
Trademark: U-ideal
Origin: Tianjin, China
HS Code: 90261000
Mass Flow Meters
Mass flow+ volume flow+density +temperature measurement+calculated variables (e.g. fluid concentrations)

Introduction of Coriolis flow meter
 
(1) The Coriolis force mass flowmeter can measure the mass flow rate directly, and won't be affected by the measured medium temperature, pressure, density, viscosity. But other kinds of mass flowmeter using indirect measurement method, to measure volume flow first, and then got the mass flow rate after compensation of temperature, pressure, density.
(2) The Coriolis force mass flowmeter inside have no moving parts, high reliability; Don't need Straight pipe before and after the installation.
(4) The Coriolis force mass flowmeter have options of all-in-one type and split type, LCD, explosion-proof type, temperature insulating model. Can output analog signal 4~20mA, the frequency signal, the RS485 communication interface and Hart protocol at the same time.
(5) The Coriolis force mass flowmeter is suitable for various liquid, such as corrosive liquid, smudgy medium, suspension, two phase liquid (gas content in liquid <10% in volume, if air content big, please add air eliminator), etc.
 
 

Coriolis Mass Flow Meters patented and developed by our company are the leading meters for precision flow measurement. And with good reason, the meters offer the most accurate measurement available for virtually any process fluid, while exhibiting exceptionally low pressure drop. The meters offer direct mass flow, volume flow, density, and temperature measurement of liquids and slurries — without the need for additional equipment, manual calculations, or estimations.
 
The meters carry hazardous area approval for P. R. China.
   

3. Warranty period: 12 months from the date of putting the instruments in operation, but not more than 18 months from the date of official shipment from our factory. 

4. Medium: Liquid OR Gas 


5. Main technical parameters
(1) Measurement scope: 2kg/h~500t/h
(2) Accuracy: ± 0.2%~± 0.15%
(3) Work pressure: (0~32) MPa (in case of other high pressure, it must be of special order)
(4) Medium temperature: -50º C~ +350º C,
Measurement accuracy: ± 1º C
(5) Environment temperature: -20º C ~ +70º C
(6) Measurement medium: Liquid, gas, solid, or two phases and three phases mixed fluid
(7) Output signal:
4-20mA current signal of flow, with load resistance ≤ 500Ω
0-10kHz frequency signal of flow.
RS485 Communication protocol
Hart protocol
(8) Power supply voltage: 24VDC
(9) Measurement of measuring pipe: 316L stainless steel
(10) Response time: 0.1s~5s, adjustable
(11) Explosion-proof grade: Ex(ib)II BT2-T5



Working principle:
The structure of Coriolis Mass Flow Meters was consisted of a pair of bended tubes. The principle is to detect Coriolis force forced a pair of tubes from inner mass flow by fluid.
A new force—Coriolis force (picture 1) would be appear while two conditions met: (1) vibrating with normal frequency in a pair of bended tubes, (2) fluid flowing in tubes. This force was produced upon synthesis from vibrating force and flowing force by fluid in tubes. And tubes would be wresting symmetric the center line because the force forced (picture2). Two displacement sensors on sides of tubes detect the force and output electric signals. The signals regulated, mass flow directly produced (picture3).
 
Density measuring: Mediums of different density flow through the sensor, the vibration frequency of the vibration pipe is different, so can calculate the medium density by the vibration frequency.
 
Temperature measuring: Platinum resistance Installed on the sensor vibration pipe can indirectly measured the temperature of the medium.
Mass Flow Meter-Coliolis Flow Meter-Measuring The Mass, Volume, Density

 

Crushers

Mineral Machinery Quarry Crusher Stone Mining PE Jaw Crusher with Spare Parts

Mineral-Machinery-Quarry-Crusher-Stone-Mining-PE-Jaw-Crusher-with-Spare-Parts

China Capacity 10-300t/H Stone Jaw Crusher for Mining

Rock Stone Jaw/Cone/Impact/VSI/Hammer/Roller Mobile Portable Crusher for Limestone/Granite/Riverstone/Basalt Quarry Crushing and Mining for sale

Crusher Machine/Mining Crusher Equipment//Rock Crusher/Stone Crusher/Hydraulic HP Cone Crusher

Mining Processing Rock Crushing Machine Stone Impact Crusher Price for Granite

High Effectivity Crusher Mining/Stone Crusher/Cone Crusher/Jaw Crusher


Jaw Crusher Brief Introduction
Our stone crusher machine, a type of jaw crusher is widely used in mining, railway construction, water conservancy project, metallurgy, chemical, building material industries. It is mainly used to crush rock and ore, whose compression strength is less than 320 Mpa. Jaw crusher, your preferred primary crusher, is used for coarse crushing and fine crushing.


Jaw Crusher Features
1. Crushes the ores,rocks ,pressure below 320 MP;
2. Easy maintenance;
3. Used in mining,building,chemical;
4. Crusher with Less machine stop time;
5. Low cost;
6. Long service life;
7. Primary crusher, simple structure;
8. Strong construction;
9. High crushing ratio;
10. Easy maintenance;
11. Stable performance;
12. Jaw crusher with Even final products

Jaw Crusher Specifications

Model

Max. feeding size

(mm)

Discharge size

(mm)

Capacity

(t/h)

Motor power

(kw)

Weight

(t)

Diemension

(mm)

PE150*250 125 10-40 1-3 5.5 0.7 1000*870*990
PE250*400 210 20-60 5-20 15 2.8 1300*1090*1270
PE400*600 340 40-100 16-60 30 7 1730*1730*1630
PE400*900 340 40-100 40-110 55 7.5 1905*2030*1658
PE500*750 425 50-100 40-110 55 12 1980*2080*1870
PE600*900 500 65-160 50-180 75 17 2190*2206*2300
PE750*1060 630 80-140 110-320 90 31 2660*2430*2800
PE900*1200 750 95-165 220-450 160 52 3380*2870*3330
PE1000*1200 850 195-265 315-500 160 55 3480*2876*3330
PEX150*750 120 18-48 8-25 15 3.8 1200*1530*1060
PEX250*750 210 15-60 13-35 30 6.5 1380*1750*1540
PEX250*1000 210 15-60 16-52 37 7 1560*1950*1390
PEX250*1200 210 15-60 20-61 45 9.7 2140*2096*1500

Jaw Crusher Working Principle
When Jaw crusher working, motor through the pulley drive the eccentric shaft rotation, from the period of hubei near, fixed jaw, and for the material such as extrusion, rolling and run multiple broken, make material from large to small, gradually whereabouts until discharge through the discharge port.



Jaw crusher applications
PE series jaw crusher is typically used as primary crusher or the first step in the process of reducing rock. They typically crush using compression. It is widely used in Mining, metallurgy, construction, highway, railroad, and water conservancy, etc.. It can process Iron ore, copper ore, gold ore, manganese ore, river stone, gravel, granite, basalt, minerals, quartz, diabase, etc...


Ore Planting Grinding Machine,Ore Plant Crusher Processing Machine,Rock Crusher Jaw Crusher Cone Crusher,Rock Stone Jaw Crusher Crushing Plant

Henan YK Prospecting Machinery Co., Ltd , https://www.yyundergrounddrillingrig.com